Feeds:
Posts
Comments

Archive for the ‘Grass combustion research’ Category

A few of our contributors have recently summarized their experiences at the 3rd Annual HeatNE Conference that was held in Manchester, NH April 14-15 and, in doing so, have nicely captured most of the “take home “ messages from the event. I was very pleased to see that grass energy had a real presence and was encouraged by the participation of so many people in the special post-conference grass energy development meeting. I strongly support folks working through statewide and regional organizations and communicating through this blog and in other ways in order to raise issues and track progress. At the national level, it is important that we participate through membership in the Biomass Thermal Energy Council (BTEC). I have suggested to our County’s Industrial Development Agency (IDA) that they join BTEC inasmuch as biomass energy development is important to our County, whether it be woody or agricultural. This would provide a conduit for informal, non-incorporated, (cash poor!) groups such as the St. Lawrence County Grass Energy Working Group to convey their thoughts to BTEC. By extension, I would encourage other county IDAs with similar interests to do the same.

Now for the topic-de-jour. I would like to focus on a conversation I had with a vendor at the Conference who, while demonstrating the features of the boiler his company had developed, made a very simple but profound statement: “You decide what fuel you want to burn and we will design a unit to burn it efficiently and cleanly”.  It became clear to me that, in order to advance grass as a fuel, the “research and development community” needs to first decide which grass species and cultivars to use, either singly or in mixtures, how to grow and harvest them in ways that will minimize ash and chlorine, how to best densify them (or not) and to document their combustion characteristics. In short, recipes for grass fuel are needed. Then, boiler manufacturers will have a fuel with predictable characteristics for which they can design their equipment. Currently, research on grass combustion is often based on the reverse sequence – different grass mixtures are tested in off-the-shelf boilers to see if they will work. Maybe you get lucky doing it this way, but it is a hit-or-miss proposition.

Having definite recipes for grass fuels would also give growers comfort. They would know how to establish stands and properly harvest them, and the value of the bio-energy crops could be more reliably predicted. Much of the speculative nature of these crops could be eliminated.

The main priority of grass energy research at this time should therefore be in developing grass fuel recipes that are: (1) adapted to regional growing conditions, (2) harvested using a standardized protocol and (3) tested for their combustion characteristics. This is a proper role for government-assisted research. Once the recipes are known, the innovation of the private sector can then be unleashed to create the desired combustion technologies.

I suspect that several manufacturers are already close to being able to claim reliable, clean, efficient grass fuel combustion performance. Some are probably already there, particularly for larger boiler systems. It is the residential market for grass-fueled heating systems that stands to gain the most from the approach described in this article. Regardless of the market sector, everyone should benefit from zeroing in on the best recipes for renewable grass fuel.

Read Full Post »

I will try to complete the overview of our installations.

The rest of the story about the Quadrafire is that we have been able to burn these stoves successfully at two locations.

We finally interfaced with the proper person at Hearth and Home Technologies who supplied us with the latest tables to burn grass pellets. The first unit that we removed was reinstalled in the dining hall at the 4H camp in Delaware County. This unit has functioned as well as we had expected from the success at Cornell University.

The second Mt Vernon was installed this fall and it too is burning grass with no major problems. The one drawback with this unit is the rather small ash pan. The inherently higher ash content of grass dictates the frequent emptying  of the receptacle and as already stated in other posts the units, stoves and furnaces, need frequently cleaning to function properly.

Last post I commented on the Central Boiler furnaces. I will now continue reporting on our other hydronic furnaces. We have placed three Woodmaster pellet furnaces into service, two ASF 1100 and one AFS 900. All of these units work very well when they are operating. The AFS 11oo are manual light that are lighted with a starter gel once lighted they burn constantly but switch to a maintenance mode when the water jacket reaches operating temperature. In this mode the unit cycles the feed and air blower on and off to maintain a small fire until the jacket temp falls calling for more heat.The AFS 900 is a newer model and has auto ignition. The pellets are ignited by an electric ignition module. When the furnace reaches operating temperature the feed stops and the fire is allowed to go out until a call for more heat and the unit re fires. There have been some issues with the feed systems especially the larger AFS 1100 . We are using large poly feed bins that were supplied with the furnaces. These larger bins require a long auger from the bin to the furnace. The bins were difficult to position in such a way as to insure the augers were straight and true. Because of this we have had breakdowns of the feed auger systems. We are working along with the manufacture to solve these issues.

We have found that Grass Bio-Fuel is a viable heat source and the problems we have experienced do not mean that this renewable energy source is too problematic to be successful. The project to date has shown that Grass Pellets can be used as a clean and efficient heat source.   It must be remembered that all of out appliances are now older technology. The biofuel industry in this country is still evolving and I think the manufacturers are beginning to address problems with these earlier products.

We have not experienced any corrosion issues to this point and have extended the project to determine how our appliances will hold up in real world setting. We also are interested in if the available units can be used successfully by the average homeowner. Some think the future of bio-energy is in larger scale  commercial installations but I for one am not ready to give up on the use of this heat source for residential use.

Catskill Grass Energy Project personnel will be at the HeatNE 2001 Conference and I hope to meet some of our readers there.

Read Full Post »

Building a grass-based bio-energy industry will require advances on three fronts: (1) creating demand through price competitiveness and heating appliance compatibility, (2) developing reliable, cost-effective densified fuel production and (3) making it worthwhile for grassland owners to produce sustainable bio-energy crops. These can be thought of as three legs of a stool, all of which must be present for the stool to stand. This brief essay focuses on the second item: developing reliable, cost-effective densified fuel production.

Although there are special systems such as those manufactured by Reka that can burn undensified fuel, densification into pellets and/or briquettes is going to be necessary for widespread adoption. Densification facilities, whether they be mobile or stationary, have to be designed for optimum production and minimum cost. People who know how to do this well can be found in the dairy and livestock feed mills that serve New York and the Northeast.

An opportunity may exist to work with one or more of these mills to test grass pellet production under real-world conditions and establish the economics. Such a research effort could be a model of public-private partnership. The ideal candidate for such a project would be a mill that has some amount of surplus pelletizing capacity. Depending on their configuration, some mills produce both pelletized feed and bulk mixtures. If the demand for bulk mixtures increases relative to pelletized feed, such a surplus capacity can occur.

The research may cause feed mills to add grass fuel pellets to their product lines or it may open the door for new entrepreneurs. In the future, densified grass fuel could be delivered in bulk to on-site storage at the points of use with the same delivery vehicles that are currently used for feed deliveries. Another approach could be the interchangeable container method, as described by Tony Nekut in the February 13 posting.

If no feed mill can be identified that would agree to participate in a funded research project as described above, another alternative would be to fund a dedicated test-bed facility. It would be economical, however, to use existing equipment located in a feed mill if possible.

I am hopeful that this is one of several issues that participants will discuss at the HeatNE Conference in Manchester, NH on April 14-15. Grass energy will have a higher visibility at this year’s conference than in the past. I encourage you to attend.

Read Full Post »

Harmon P68 fired with Grass at the Ashoken Center

There have been several requests for me to explain our experiences burning grass pellets in the appliances being used the Catskill Grass Bio-Energy project.

(Please note:  any mention of brand names is for informational purposes only, and is not intended as an endorsement of a particular product.)

Our first purchases were two Quadrafire Mt. Vernon pellet stoves. One was quickly installed and the other put in storage for later installation. We also purchased two Central Boiler Maxim pellet hydronic furnaces. One was sited at the Town of Franklin NY Town Garage where the first Quadrafire was installed in the Town meeting hall in the same building. We were able to secure the services of a local plumber who completed the installation by the end of December that first year.

Initial operation of these first units had a steep learning curve. The Maxim furnace burned well after the operator at that site tried many combinations  of feed rates and blower settings. Neither the manufacture nor the local dealer were of little help tailoring the settings to burn grass. Luckily the operator at the site had a lot of experience in the heating industry and had interest in making the unit work to its potential. As the season grew colder we found that if the unit was pushed to produce maximum heat it had a tendency to melt the aeration paddle on the end of the feed auger. The original was mild steel but the replacements were made of stainless steel. They did last longer but eventually failed as well. We kept replacements on site after the third failure. Another shortcoming of this unit is the size and position of the ash drop. Ash has to be removed by scooping the ash out daily also the unit has to be shut down weekly to clean the interior of the burn area and the heat exchanger. If this is neglected the unit pushes smoke back into the hopper on top of the furnace leaving a creosote type of condensate in the hopper. Another problem with the design of this unit caused two burn backs into the top hopper. We are not sure the reason for the first but the second was the result of a power outage lasting six hours. The unit needs a supplemental power source to run a clean-out cycle if high heat is experienced or a power outage is experienced. By the way, the unit was burning wood pellets at the time of the power outage.

As to the Quadrafire at this site, the operator tried all season to burn grass with little success. Any of the settings on the control unit did not dump the ash fast enough and the fire was snuffed out. We purchased these stoves based upon the success of Dr. Cherney at Cornell University. We knew we needed specific tables to burn grass successfully. Dr. Cherney supplied us with the tables that the manufacture had supplied. We were unable to install the grass tables. We sought help from several Quadrafire dealers and the manufacture and were told multiple times that Quadrafire does not support burning grass pellets even though we knew grass tables existed. After that initial season we pulled the unit and replaced it with a Harman P68 which has been burning well ever since. The Harman has analog controls for feed rate and also has a unique burn system where the pellets are pushed up a burn ramp and the ash is pushed off the ramp into a very ample and removable ash pan.

We have four Harman stoves on site at this time, Two P68s and two P45s. These units are working well burning grass pellets, but, like all appliances burning grass, they require frequent cleaning. Anyone wishing to burn grass with  appliances that are not specifically designed to handle grass will need the owner/operator to be conscientious about operation and cleaning.

More about the Quadrafire saga (we are using them satisfactorily)  and our other appliances and installations next time.

Keep Warm!



Read Full Post »

I often feel like I am having trouble keeping up with the current status of grass energy research and development. Just when I think I have a grasp of the scene, I get surprised by some new revelation. This happened most recently when I downloaded the Technical Assessment of Grass Pellets as Boiler Fuel in Vermont. This 46-page report was produced by the Vermont Grass Energy Partnership, a collaborative effort among the Vermont Sustainable Jobs Fund, University of Vermont Extension Service, and the Biomass Energy Resource Center in Montpelier (BERC). Various people have critiqued this report in this blog and elsewhere and I am not planning on using this space to give it a full review. Despite its flaws, real or perceived, I applaud Vermont for supporting grass energy research and development through the Sustainable Jobs Fund and wish that New York State had a similar commitment.

The Vermont study was by its own admission limited in scope and will therefore prompt further research. Citing the report’s “Next Steps” section:

The next steps in determining the feasibility of grass energy in Vermont should include a robust economic assessment of the costs of manufacturing grass pellets under different scenarios. For instance, what changes can be anticipated at a centralized (stationary) pellet mill compared to utilizing mobile equipment (at different scales) to process the grass “on location?” As part of this economic assessment, key variables such as the cost of energy (fuel, electricity, diesel, biodiesel, etc.), subsidies paid to farmers (e.g., USDA’s Biomass Crop Assistance Program), and economies of scale in production costs must all be considered. Once the grass pellet production costs are fully understood, target wholesale and retail price points can be projected and compared against other heating fuels, including liquid fossil fuels and wood fuels.

As part of these next steps, the report also states that research will be needed to:

• Examine new and existing heating appliances (furnaces and boilers) that claim the ability to reliably burn high-ash fuels such as grass pellets.
• Determine the production costs of pellets made with grass and wood blends and to gauge the interest of the pellet consuming market for this type of product.
• Assess the production costs of farm-scale grass pelletization and the potential fuel savings of grass pellets over other heating fuels. Other market development scenarios using 100% grass pellets could emerge that will need further in-depth analysis as well.

That’s a decent grass pellet research agenda. Recently, the Vermont Sustainable Jobs Fund issued a request seeking proposals that will: “…. lead to the design, fabrication, demonstration and use of a mobile or stationary pelletizing system capable of converting at least 1-ton of grass biomass per hour into densified fuel. Projects must be able to identify at least one in-state source of grass biomass that will be pelletized and at least one in-state end-user of the pelletized fuel.”

Others, notably Renewable Energy Resources LLC and Broome Biomass LLC are researching briquetting (or cubing) densification as well as feedstock harvesting and handling methods to produce grass fuels for larger boiler/CHP applications. Still others, such as Jerry Cherney at Cornell, Michael Newtown at SUNY Canton and Paul Cerosaletti of Delaware County Cornell Cooperative Extension are examining the combustion characteristics of grass fuels in commercial and residential-sized units. Also, we should not fail to mention the mobile pelleting work of the Hudson Valley Grass Energy Group and the Pocono-Northeast RC&D Council in Pennsylvania. Last, the work of the Resource Efficient Agricultural Program (REAP) in Ontario, Canada is well known.

My intention here is not to try and provide an exhaustive listing of all the research that may be ongoing, but rather to ask the question: “Are we, the grass energy community, covering all the research and development bases in a coordinated and comprehensive way?” Yes, different people are looking at different pieces of the puzzle, but are we really working together in a truly collaborative manner? Perhaps it is time to convene a special-purpose conference for the relatively small cadre of researchers and business interests to review progress, compare notes and chart out a research and development course that will get us to the goal of a viable grass energy industry.

Read Full Post »

The Vermont Grass Energy Partnership recently released a report titled “Technical Assessment of Grass Pellets as Boiler Fuel in Vermont”. A more fitting title would be “Yet another demonstration that grass biomass can be pelletized and combusted but is a more problematic fuel than wood”. The study does demonstrate the process, but it offers little if any new technical information, and I question why this work was even considered for Federal funding unless its proposed scope was more ambitious than what is represented in the final report. The topics covered in the report have all been addressed, and in much greater detail, by previous research. Indeed, the references cited in the report’s own bibliography, in particular the one by Jenkins, et al., contain far more useful technical information on slagging, corrosion, and emissions than this study. I have included a list of articles below. The length of the list is limited by the blog word count, not by the number of relevant references: there are dozens in addition to those listed and they can easily be found via web search. This is not to say there remains no worthwhile research to be done.

The problematic characteristics of grass fuel remain mostly unaddressed and call for work on innovative solutions. The mechanical problems related to ash fusion and clinkering have been largely dealt with already in multifuel boilers. Fuel leaching by natural or artificial means can also be employed to remove much of the low fusion temperature alkali chloride ash components. This also reduces the corrosive effects of chlorine in the flue gas. Another option is microground grass fuel burned as an explosible air entrained powder. In this case, the ash particles cool before they have a chance to agglomerate. I do not believe that the clinkering issue presents much of a technical challenge, except for residential scale pellet stoves which, for the most part, are not yet designed to have multifuel capability.

The corrosion and emissions issues posed by grass fuels are more difficult. Obviously, reducing the nitrogen, sulfur, and chlorine content of growing grass is the most straightforward approach. Grass type, soil chemistry, and fertilization practices all impact the chemical content of the growing grass and harvesting practices further impact the final chemical composition of the feedstock. I am not an agronomist and am ill informed about ongoing research in this area. I think it’s safe to say that standard best practices have yet to be established. Properly designed multifuel boilers use corrosion resistant materials and can reliably combust grass fuels. As mentioned above, chlorine content can be reduced by leaching and NOx and PM emissions can be reduced to some extent by carefully controlled staged combustion and exhaust gas recirculation. Finally, there are well established methods for flue gas scrubbing that can be employed if necessary. Cost effective small scale flue gas treatment methods need further development work.

I was surprised that the report contained no information regarding important details of grass pelleting, in particular how the process must be modified with grass and grass/wood mixtures. Were different dies used? What other process parameters were modified?

Finally, I think we should be looking at other grass fuel forms aside from pellets. Just as with woody biomass, which is typically burned as chips in non-residential boilers, baled grass is the form of choice for lowest cost local use. Efficiently stacked or containerized bales can have an effective bulk density of 15-20lb/cuft, comparable to wood chips. In my next blog, I will discuss the merits of containerized bulk biomass solutions.

PS – I apologize in advance for my negative reaction the Vermont study. My opinion is just that, and is not intended to impugn other efforts by the members of the Vermont Grass Energy Partnership.

References – available on the internet for free

Thomas Nussbaumer
Combustion and Co-combustion of Biomass: Fundamentals, Technologies, and Primary Measures for
Emission Reduction
,
Aerosols from Biomass Combustion

B.M. Jenkins et. al.
Combustion properties of biomass

E. Bjorkman and B. Stromberg
Release of Chlorine from Biomass at Pyrolysis and Gasification Conditions

Peter Glarborg

Hidden interactions—Trace species governing combustion and emissions

References – available on the internet for a fee

P. A. Jensen et.al.
Transformation and Release to the Gas Phase of Cl, K, and S during Combustion of Annual Biomass,
Pretreatment of straw for power production by pyrolysis and char wash,
Removal of K and Cl by leaching of straw char,
Experimental Investigation of the Transformation and Release to Gas Phase of Potassium and Chlorine during Straw Pyrolysis

Read Full Post »